Compatible Systems MicroRouter 900i Uživatelský manuál Strana 91
- Strana / 94
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Section 12 - Index - 91Microrouter CNC Machine User's Manual
Index
F
FAQs...................................................................67
Feedrate override...............................................30
G
G codes listing....................................................73
General layout of machine ................................24
Glossary .............................................................87
H
Help (technical support) .....................................66
I
Interlock guard switch .......................................12
Introduction
microrouter ....................................................7
what is CNC?...............................................8
L
Laminate trimmer
maintenance..................................................61
refitting............................................................38
removing .......................................................34
setting tools ...................................................36
Leadscrew lubrication .......................................51
Levelling your Microrouter................................16
Lifting your Microrouter...................................... 14
Lubrication
areas on the Microrouter..............................50
chart ...............................................................48
leadscrews ...................................................51
sliderails ........................................................54
M
M codes listing ...................................................74
Maintenance
general work area cleaning.........................49
laminate trimmer ...........................................61
schedule........................................................48
Microswitches (cleaning) ..................................58
N
Noise level test results......................................85
12: Index
A
Address characters listing.................................75
Advantages of CNC ..........................................8
Axis definitions ...................................................26
C
Clamp rails
assembling....................................................41
components...................................................40
using ..............................................................43
Clamping
vacuum table ................................................44
work holding clamp rails .............................40
Cleaning
general information .......................................49
laminate trimmer ...........................................61
leadscrews ...................................................51
microswitches ..............................................58
sliderails ........................................................54
thrust bearing couplings ...............................57
CNC (definition and overview) ........................8
Connecting
schematic diagram showing connections .22
the dust extraction system..........................20
the PC to the Microrouter .............................17
Contact information ............................................2
D
Denford directives listing ...................................76
Denstep motion control board ...........................64
Disclaimer ...........................................................5, 6
Dust extraction....................................................20
E
EC declaration of conformity.............................83
Electrical diagrams ............................................17
Electronics
accessing the panel .....................................62
denstep motion control board ......................64
layout of panel ..............................................63
spindle drive board ......................................65
Emergency stop button .....................................11
Equipment lists ...................................................9
- Microrouter 1
- CNC Machine 1
- User's Manual 1
- Contact Information 2
- Contents 3
- Warning Notices 5
- About this Manual 6
- 1: What is CNC? 8
- Safety Features Overview 10
- Safety Precautions 10
- 3: Levelling your Microrouter 16
- 3: Electrical Diagrams 17
- Dust Extraction Systems 20
- 9 to 25 Pin D 22
- Serial Cable* 22
- (see Note * left) 23
- Lefthand and Rear 24
- Cabinet Layout 24
- Front Cabinet 24
- 4: Part Manufacture 29
- Checklist and Tool Changing 29
- 5: Performing a Tool Change 32
- Machine Head 34
- Removing a Tool 36
- Refitting a Tool 36
- Vacuum Table Troubleshooting 47
- Lubrication Chart 48
- Maintenance Schedule 48
- 7: General Work Area Cleaning 49
- 7: Lubrication of Leadscrews 51
- 7: Lubrication of Sliderails 54
- X Axis Datum Microswitch 58
- Y Axis Datum Microswitch 59
- Z Axis Datum Microswitch 60
- Failure to Start 61
- Lubrication 61
- Brush Inspection 61
- Display 64
- 8: The Spindle Drive Board 65
- 9: Technical Support 66
- 9: Troubleshooting 67
- 10: What is a Part Program? 71
- Part Program example 72
- 10: G Codes List 73
- 10: M Codes List 74
- 10: Denford Directives 76
- 10: Understanding Offsets 78
- The cutting tip 82
- EC Declaration of Conformity 83
- 11: Glossary 87
- 12: Index 91
- 12: Notes 93
Související produkty a manuály pro Sítě Compatible Systems MicroRouter 900i
Sítě Compatible Systems 1250I Uživatelský manuál
(26 stránky)
(26 stránky)
(2 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce